|
   
Iscar Offers A Completely New Family Of Slitting Cutters Utilizing Tang-Grip Technology And The Sturdiness Of Sumo Tec Grades
Iscar now offers a family of high-performance slitting tools that merge the convenience and security of Tang-Grip clamping with the increased strength of the new Sumo Tec insert grades.
The notion, already proven effective in Tang-Grip parting tools, has now been extended to slitting cutters. In the patented Tang-Grip clamping system, inserts are press-fit into their pockets with a special hand tool, and are clutched solidly in place without the need for clamps, upper jaws or set screws that can weaken the insert and obstruct chip flow. The pocket design utilizes cutting forces to keep the insert seated securely in position, eliminating any prospect of insert pull-out. The Tang-Grip clamping system also fosters additional accurate slitting cuts plus lengthened pocket and insert life.
Iscar's Sumo Tec insert grades showcase a special post-coating treatment which extensively improves tool life and reliability.
Introduced in late 2007, the unique Sumo Tec treatment flattens the insert's coated surface to eliminate microscopic stress raisers, diminish heat and friction and improve chip flow. The result is enhanced toughness and resistance to chipping and built-up edge, all leading to longer tool life. The golden-colored side on Sumo Tec inserts eases wear detection. Size for size, Tangslit cutters give more teeth than Iscar's SGSF cutters, enabling higher feed rates.
Their increased rigidity leads to straighter, more accurate cuts and reduced vibration even in large-diameter cutters. The new Tangslit TGSF cutters come in 100 to 160 mm diameters, 3 and 4 mm widths and can accommodate the exact same selection of inserts as Tang-Grip parting tools. Some other sizes will be added.
Obtainable Sumo Tec grades for Tangslit cutters include:
IC808, with a tough submicron substrate below a Sumo Tec TiAlN PVD coating, offering exceptional resistance to impact loads and built-up edge. This grade is recommended for slitting heat resistant alloys, austenitic stainless steel, hard alloys & carbon steel.
IC830, offering extra toughness for heavier parting and grooving including interrupted cuts. It is appropriate for every stainless steel and high temperature alloys.
IC908, a hard, fine-grain substrate with outstanding chipping resistance, combined with a completely new Sumo Tec TiAlN PVD coating. It is ideal for nodular or gray cast iron.
IC928 and 928A, PVD TiAlN-coated tough grades suitable for stainless steel, high temperature alloys and other alloy steels. These grades are likewise favored for interrupted cuts and heavy operations.
Every Tangslit and Tang-Grip inserts are available in J- or C-type chipformer geometries from Iscar.
Push Pull Testing For Highway Industry Supplying Calibrated Gauges. Mechanical Load Testing Methods For On Site Proof To Testing Requirements.
Push Pull Testing for the Railway industry for proof of reliable anchor fixings. Calibrated push pull force gauges are used for stress load testing along with tensile strength pull testing procedures. Proof of load testing undertaken, measured, recorded in a reliable and standard way to BS5080 Part 1 standards.
The Newest In Carbide Endmill Configuration In A Extensive And Successful Line From Iscar
Manufacturers and die & mold shops can eliminate chatter problems in many milling operations with Iscar's new Chatterfree endmills. The cutters' variable-pitch flute pattern eliminates harmonic vibration, the main source of chatter. This enables faster cutting and finer finish in rough or finish slotting, shoulder milling and cavity milling.
Iscar Recently Made Public Numerous New Lines To Increase Their Family Of Milling Cutters
Iscar recently released a new family of High Speed Milling adjustable endmills and facemills that will improve milling of aluminum, non-metallics, cast iron and hardened steel. This should prove especially useful in the automotive and aerospace industries.
Original Tools And Carbide Insert Arrangements From Iscar To Better The Machining Process
Iscar is introducing Penta 34 carbide inserts with a new PB chipformer. The PB chipformer features a single cavity with a positive rake, neutral shoulder angle, and a honed edge. It is actually a C-type chipformer with a different frontal edge.
A Handful Of Developments In Carbide Inserts Thanks To Iscar Over The Former Decade
Iscar is announcing a brand new unique milling system that includes tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has meaningful advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, decreased cutting forces resulting in better performance.
Industrial Water Heater - Considering All Of Your Requirements - Read Cautiously In Order To Know More
Looking into a commercial water heater? Then you have a few things that you must consider. Take a look at these areas to avoid making a mistake with the wrong unit.
Automotive Manufacturing Jobs - What To Look For And Why.
There is no point in denying that workers serving in the automotive industry are also suffering from the economic recession that everybody is experiencing world wide.
Related Posts
Associated Resources
|